goggles

...now browsing by tag

 
 

Lesson 34 – 21st September 2009 – 1050 – 42 minutes – Total so far – 35 hours 28 mins

Monday, September 21st, 2009

Well, despite poor weather, we managed to get a lesson in, albeit a short one (40 minutes).

We concentrated on instrument flying, but managed some autos and a demo’ed auto with power termination in a field near Morpeth.

Order of the day….I booked out, and checked G-MAVI over. There was some confusion with our callsign. I’m sure I put Northumbria01 on the booking out sheet, but Tower queried our callsign, they were happy for us to assume the mantle Northumbria01 instead of ZERO TWO.

Steve came out for the last couple of checks and we were told to hold at Foxtrot. That was good, because I got chance to do a couple of landings/takeoffs as we waited for a plane to land and taxi off the active.

Once he’d gone, we were given the go. Once we’d climbed to about 1600 feet (we couldn’t have gone much higher because of the cloud base), Steve had me don the instrument goggles. Usual…

  • hold a heading
  • turn 90′ left
  • turn 90′ right
  • Descending 180′

They all went fine.

Steve then took control and adopted an unusual attitude in the plane and with the instrument goggles on,  I had to get us level again. I got it eventually, but it took me 5 seconds to realise power was low. Once I’d sussed that, it was sorted.

Once the instrument flying was done, I was a bit disoriented. I had no idea where we were, what direction we were facing. And I’m pleased about this, because it made me think about where the wind was coming from and that normally I don’t have to do that. It shows me I’m developing a constant awareness of the wind direction without realising it at the time.

We did some autos to a powered recovery at about 500 feet. I needed reminding about the throttle. We did a couple of max range ones where we reduce rotor rpm to 90/95% whilst maintaining 75kts.

By this stage, my concentration was going, and I wasn’t benefitting from the practice, so I asked Steve if he’d demo an auto to 5 feet above the ground. We had a nice field with the only downside being some sheep in one corner, but they were totally unphased by us even after we’d climbed away. They were a few hundred yards away.

It was interesting to watch an auto being done all the way to a low hover. It allowed me to analyse and think it through, plus Steve through in a commentary. His commentaries, because they are the same language each time DO help learning a lot. It’s a set of instructions that gradually sink in, so that when I do it, I’m hearing Steve saying things like……

  • Balance, check
  • Rotor RPM, check
  • Reduce Throttle, check
  • Speed, check
  • Cancel Carb Heat
  • Not yet, not yet, not yet
  • Flare
  • Level
  • POP (that’s his favourite)
  • Cushion

He says these exact things everytime, and the fact I can write them down, tells me they are sinking in. Of course, doing them is another thing, but I’m getting there.

We’d been out 25 minutes and I wasn’t in the zone today, so Steve (rightly) suggested we head back. He’d spotted a fast low-level helicopter on the way back. We kept a visual with it until it was in front of us.

Tower :- Report at Stannington, join right-base for 25. QFE 1010.

We did that, and Steve said to use the approach to practice the approach sight picture. The sight picture is how an approach should look. I need to start doing this on every final to the runway, because, as Steve said, you don’t often get a mile long runway to practice your “sight picture”. Good tip.

The final landing was a pleasing one. I’ve decided not to fart on any more. Scott was right, get yourself ready for a landing and barring any sideways/backwards movement, commit to getting it down. I did it today, and it worked. It wasn’t 10/10, but it was 9/10. I was happy.

No lesson until friday, because of kp stuff. There may be an opportunity of a cheap cross country to Blackpool. All day job for a heli to have a service. So, I hope that comes off, as I did all my light aircraft flying from Blackpool, so that will be a trip down memory lane. PLUS Steve said we may get the chance to look around the Oil Rig helicopters there. Fingers crossed for that one.

Lesson 31 – 15th September 2009 – 1005 – 1 hour – Total so far – 33 hours 22 mins

Wednesday, September 16th, 2009

Another great lesson today.

We started with a discussion about what to do. It was clear I need to get my solo hours up as I’ve only got about 2.25. The prospect of going to X and back without landing didn’t really appeal to me, so I suggested a trip to Carlisle and back to land away and Steve said that was ok. Sadly, the weather precluded the trip, but it’s an exciting thought for the future :-)

Instead we did some more instrument work (I need to get instrument hours up too) and some confined area landings which made out for an excellent and fun lesson.

Steve came out with me today to see how I was checking her over. That was good because it was some reassurance that I was doing 90% correct, but also reaffirmed and refreshed some of the names of helicopter parts and their function and things to check. I was quite surprised to find out that this isn’t tested in the General Flying Test (GFT). But, I expect it’ll be needed for the commercial test, so all is not lost and this is essential stuff anyway.

We started her up and we’re off to Foxtrot to hold for a 07 departure. Quite busy for departures so we held in the light aircraft warm-up area. Here I was presented with the choice of hover practice or putting her down. I felt the need for some landing practice, so whilst we waited, we did some landing/liftoff combos, probably about 3 or 4. I did a 10/10 one which always leaves me feeling warm inside, and a couple of 6/7′s. We were then asked to line up and wait.

No sooner had we “lined up” we were given the go and off we jolly well..….

Once at level flight, Steve had me don the instrument goggles so I could only see the instrument pedestal. He asked me to …..

  • Hold a heading
  • Climb 300 feet
  • Descend 300 feet
  • Turn 90′ to the left
  • Turn 90′ to the right
  • Do a 180′ descending turn

All on the way to the confined area.

It all went well.

Then we approached a different, more confined area than previously.

The wind was a Northerly wind, but the area was naturally west-east, which meant it was a bit of a challenge. The wind was also quite light about 5 knots, so given the direction that was probably a plus.

We did the powering back to 53knots level to find the available MAP. We had 6.5 in hand. This reminds me, before I forget, a joke from yesterday. We had the same amount of MAP available yesterday (6.5 inches).

Steve :- So, you have 6.5 inches in your hand, I mean “in hand”

LONG 5 SECOND PAUSE as dp is concentrating so hard.

The joke hits. Late laughter ensues !

Steve finds the time it took for the joke to work funny. I’m laughing at the joke etc etc…..We have a laugh for sure !

Anyway, back to today. After doing the S’s checks and with our 6.5 inches IN HAND, we were spoilt for choice for the approaches. We initially tried a west to east approach to make the most of a gap in the trees and the more lengthy runway-like shape of the confined area, but at the decision altitude, it didn’t feel right so I suggested going around. The wind was more northerly than forecast.

With the wind being so light, Steve suggested a southerly approach as there were less trees on the last few yards of the approach. This made it a downwind approach which always gets my heckles up, but Steve (as always) was bang on. The lack of trees (small shrubs instead) allowed us to get lower and use the confined area for more of a flare. It worked well.

So, once in the confined area in the hover, we did the “move to the right, turn right” routine and then taxi’ed to a point close to the edge of the area. We had enough power for a towering takeoff and Steve had me pick a 12pm, 3pm reference. Once I had them, we pulled 24.5 MAP and we shot up. Once clear of the trees, we transitioned away. It should look great on the video.

We did another orbit and approach and picked a different location in the confined area for the towering takeoff. For the second one, I started the transition a little early, but you live and learn.

We then headed back to EGNT. Steve did an “Engine Failure Engine Failure etc” on the way back. Did the “entering” fine, totally forgot the Mayday call which come to think of it, I forgot yesterday too. It was a 180′ auto, and the field I picked wasn’t as good as the one Steve had picked, so we changed to his one. It was a big field of newly harvested wheat awaiting the farmer to come round with his combine.  Steve said to go to “powered termination” so we went right down to 5 feet or so. The flare went really well and the pop of the collective and subsequent recovery are a bit of a blur, but there was a lot of yawing, but we made it back into a hover. Still need lots of work on the powered termination and the Mayday call. But, I’ll get there. Steve looked back as we transitioned off and said we’d made a mess of all the nicely rowed hay and that the farmer wouldn’t be best pleased and we should give it some wellie. It made me laugh. We had made a big circle of hay. Hope it shows on the video.

We then headed back home.

I made the call to rejoin the Zone quite late (my bad), so we started doing an orbit as there was so much radio chatter going on, I couldn’t get a word in edge ways. But, half way through the orbit, we were cleared to join.

The trip back was uneventful. The landing was a 6/10.

Next lesson is Friday and I may be going solo to Carlisle (weather and machines permitting). Looking forward to the most expensive bacon buttie you can buy. That’s not because the cafe is expensive at Carlisle….It’s a poor helicopter costs joke.

While I remember, I’m already starting to put my training head on. When I used to be an IT trainer, I used to have to think of ways to get concepts across to students in an easy to visualize/remember way. Subconsciously, I’m already starting to think about how to get helicopter concepts across. I’m sharing this in case it will help others with a problem I had. Occasionally, we fly in the HP model of the R22. It lifts off and lands differently to the non-HP variant because of it’s more forward CoG. I was sharing this with Steve as it helped me get my head around the difference. To experience the difference, try the following…..

  • Take your shoes off and put them together in front of you while you sit down, toes facing away.
  • Grab both shoes with one hand in such a way that when you lift them gently and slowly off the floor, the toes of the shoes are the last thing to leave the floor.
  • You now have your own R22 HP.

As you lift them off the floor each time, analyse the angle of the shoes.  When the heels are 1 inch off the ground and the toes still touching, how would you get the shoes level again, what movement of your hand (cyclic stick) would be needed to get the (shoes) heli level.

Also, you can mirror the double landing of the R22 HP. Lower the shoes until the toes are touching, think about what movements are needed as you get the heels down, to stop the helicopter moving backwards. Hard to explain in a blog post, but have a play.

Here’s the video from yesterday’s confined area…….Today’s will be tomorrow.

Lesson 30 – 11th September 2009 – 1134 – 1 hour 6 minutes – Total so far – 31 hours 22 mins

Friday, September 11th, 2009

Yesterday, after the lesson with Steve I was confident that I could have done another lesson had I booked it. I was refreshed and ready to fly more.

So today, I had booked 2 lessons but I was so exhausted after one, that I called it a day. Why ? Because we did Confined Area Landings, and I found it VERY mentally draining.

Today’s lesson was with Scott. I normally fly with Steve. Scott and Steve have quite different training styles. Steve’s cool, calm (and fun) approach gets the best flying out of me (Yes Steve, that’s my best ! ;-) . Scott’s full-on approach is more challenging and although I probably learn more, I get flustered and don’t fly at my best, but I do enjoy the challenge immensely.

So, today’s lesson and another beautiful day for it. Hardly any wind at EGNT. Scott was there as I did the pre-startup,post-start checks. I was doing his checklist flow, but forgot about switching the radio off before starting. A good habit to get into in case I fly an older model where the starting current can blow the radio.

For some reason, Tower had a problem hearing me. We weren’t sure if it was my headset or Tower was doing something else when I called for clearance. Later transmissions seemed to be heard fine. Although, Scott had problems hearing me. Will need to keep an eye on that. Or probably better to keep an ear on it !! I think we sorted it later by me pushing my volume up, but it’s a bit of a blur.

We taxi’ed to Foxtrot and were asked to Line up and Wait on 25. That’s a first for me in a helicopter.

No sooner had we got in position than we were given the “GO”. Once we were on the climb after the initial turnout, it was instrument time. We’d forgot the goggles, but to be honest it didn’t make any perceivable difference. Once you focus solely on the instruments, the scanning you need to do stops you looking out anyway. The only downside is you don’t know how much your peripheral vision is helping you out, but I didn’t feel like it was helping much.

So, we did climbs, turns by instruments and they went fine. I think I stayed within 100 feet of any altitude and the headings were +/- 15′, so I was happy with that. At this point, I was feeling in control of everything and on top form mentally.

As the flight progressed, the headset problems left Scott a bit frustrated. I was struggling to hear him over the radio banter. I think I needed to tweak some headset knob, but we were too engrossed to bottom it out, or at least I was. His frustration with my headset, started getting me on edge and my performance started to wane a little.

Once we’d done the instrument flying, we concentrated on Confined Area Landings. Scott had done an excellent and extremely thorough briefing before we even took off and I felt full with information, overflowing even. But, often, things are easier when you actually do them.

So, confined area landing as far as I can remember, involved a recce circuit to work out angles of approach the confined area, and possible departure angles. Then a lower circuit (approx. 1,000 feet) to look for any obstructions etc..….

Then an approach with an abort decision altitude to attempt a landing, but with a decision to abort if anything untoward is spotted.

On one of the downwind legs, we rolled back to 53 knots, maintaining level flight and recorded the power required, which I think was 17.5 MAP. Take that away from 23.5 MAP (max continuous for today), gave us 6inches MAP to play with. Ample for a confined area approach. The first attempt, I had misunderstood and thought we were going to go around, so I was too high to get in, which is what Scott wanted. With me now understanding we were going all the way in to a 5 foot hover, we did a tight circuit for a second attempt.

It felt quite a shallow approach given the steep approaches I did with Steve yesterday. My understanding after yesterday’s lesson was that it was a steep approach, but Scott had me come in quite shallow. But, we made it this time, although I did lose balance which nearly required Scott’s intervention. He was at full alert for a second before I got it under control. Not even sure why it got out of balance. Weird. I was pulling collective, which normally requires left pedal, but I had needed to give right. Bizarre !

Anyway, we came to the hover in this kind of dip in a hill and we had raised ground all around us. It was great. We then did some pedal turns, but cleverly, he had me move the helicopter to the right, before giving right pedal. In this way, we’re sure that the tail rotor isn’t going to hit anything as we’ve just come from the place the tail rotor is going to turn through. Then when we’ve done 90′ turn, we rinse and repeat until we’ve scanned the whole area. It worked a treat and the tail rotor didn’t hit anything ;-)

With the area now clear for departure, we needed to work out how much power we had available. I think we were showing 23.5 to to hover in ground effect (IGE), leaving only 1inch of MAP to spare, so we ideally needed to do an on-the-skids takeoff. But as we hadn’t landed, this wasn’t possible, so we had to do an IGE transition. It worked a treat and we headed back to Newcastle :-)

On the way back, we had a nice view of a Tornado streaking past. Hopefully, I caught it on video. Will check tomorrow if I get time. Steve was with his student at the plateau at the same time we were there and both helicopters were flying back at the same time. And I think Steve’s student had the better view of the Tornado, which isn’t necessarily a good thing ! ;-)

We followed Steve’s helicopter back and although it wasn’t quite a formation landing, we were only half a mile behind them on Base Leg and down the runway which was neat.

We taxi’ed back and then I did a shitty landing, rating of 4/10 on the dp landing scale. There was sideway’s movement at the just wrong moment, so I had to lower the collective to plant us on firmly, avoiding Dynamic Rollover.

All in all, a hectic, very taxing, but thoroughly enjoyable experience. I’ll need much more practice at these, but Scott was very complimentary about the first attempt, which was well received. I always think I’m doing worse than I am. I think it’s because I’m not flying my best with Scott generally. I haven’t done a good landing with him yet !

I’m writing this and sense myself being far too self-critical, but that’s me. It’s the way I improve I think by critiquing myself harshly. Always nice to be told that it’s gone well though.

Lesson booked for everyday next week apart from Thursday.