downside

...now browsing by tag

 
approach area auto autorotation autos carlisle couple day fingers Flight fly friday headset heli helicopter hover Instructor instrument land Lesson liftoff mavi mayday newcastle Northumbria Performance r22 robinson rpm runway Scott solo Steve takeoff test time today Tower transition trip way weather week wind work
 

Lesson 34 – 21st September 2009 – 1050 – 42 minutes – Total so far – 35 hours 28 mins

Monday, September 21st, 2009

Well, despite poor weather, we managed to get a lesson in, albeit a short one (40 minutes).

We concentrated on instrument flying, but managed some autos and a demo’ed auto with power termination in a field near Morpeth.

Order of the day….I booked out, and checked G-MAVI over. There was some confusion with our callsign. I’m sure I put Northumbria01 on the booking out sheet, but Tower queried our callsign, they were happy for us to assume the mantle Northumbria01 instead of ZERO TWO.

Steve came out for the last couple of checks and we were told to hold at Foxtrot. That was good, because I got chance to do a couple of landings/takeoffs as we waited for a plane to land and taxi off the active.

Once he’d gone, we were given the go. Once we’d climbed to about 1600 feet (we couldn’t have gone much higher because of the cloud base), Steve had me don the instrument goggles. Usual…

  • hold a heading
  • turn 90′ left
  • turn 90′ right
  • Descending 180′

They all went fine.

Steve then took control and adopted an unusual attitude in the plane and with the instrument goggles on,  I had to get us level again. I got it eventually, but it took me 5 seconds to realise power was low. Once I’d sussed that, it was sorted.

Once the instrument flying was done, I was a bit disoriented. I had no idea where we were, what direction we were facing. And I’m pleased about this, because it made me think about where the wind was coming from and that normally I don’t have to do that. It shows me I’m developing a constant awareness of the wind direction without realising it at the time.

We did some autos to a powered recovery at about 500 feet. I needed reminding about the throttle. We did a couple of max range ones where we reduce rotor rpm to 90/95% whilst maintaining 75kts.

By this stage, my concentration was going, and I wasn’t benefitting from the practice, so I asked Steve if he’d demo an auto to 5 feet above the ground. We had a nice field with the only downside being some sheep in one corner, but they were totally unphased by us even after we’d climbed away. They were a few hundred yards away.

It was interesting to watch an auto being done all the way to a low hover. It allowed me to analyse and think it through, plus Steve through in a commentary. His commentaries, because they are the same language each time DO help learning a lot. It’s a set of instructions that gradually sink in, so that when I do it, I’m hearing Steve saying things like……

  • Balance, check
  • Rotor RPM, check
  • Reduce Throttle, check
  • Speed, check
  • Cancel Carb Heat
  • Not yet, not yet, not yet
  • Flare
  • Level
  • POP (that’s his favourite)
  • Cushion

He says these exact things everytime, and the fact I can write them down, tells me they are sinking in. Of course, doing them is another thing, but I’m getting there.

We’d been out 25 minutes and I wasn’t in the zone today, so Steve (rightly) suggested we head back. He’d spotted a fast low-level helicopter on the way back. We kept a visual with it until it was in front of us.

Tower :- Report at Stannington, join right-base for 25. QFE 1010.

We did that, and Steve said to use the approach to practice the approach sight picture. The sight picture is how an approach should look. I need to start doing this on every final to the runway, because, as Steve said, you don’t often get a mile long runway to practice your “sight picture”. Good tip.

The final landing was a pleasing one. I’ve decided not to fart on any more. Scott was right, get yourself ready for a landing and barring any sideways/backwards movement, commit to getting it down. I did it today, and it worked. It wasn’t 10/10, but it was 9/10. I was happy.

No lesson until friday, because of kp stuff. There may be an opportunity of a cheap cross country to Blackpool. All day job for a heli to have a service. So, I hope that comes off, as I did all my light aircraft flying from Blackpool, so that will be a trip down memory lane. PLUS Steve said we may get the chance to look around the Oil Rig helicopters there. Fingers crossed for that one.

Posted in Helicopter Training | No Responses »
Tags: , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

Lesson 30 – 11th September 2009 – 1134 – 1 hour 6 minutes – Total so far – 31 hours 22 mins

Friday, September 11th, 2009

Yesterday, after the lesson with Steve I was confident that I could have done another lesson had I booked it. I was refreshed and ready to fly more.

So today, I had booked 2 lessons but I was so exhausted after one, that I called it a day. Why ? Because we did Confined Area Landings, and I found it VERY mentally draining.

Today’s lesson was with Scott. I normally fly with Steve. Scott and Steve have quite different training styles. Steve’s cool, calm (and fun) approach gets the best flying out of me (Yes Steve, that’s my best ! ;-) . Scott’s full-on approach is more challenging and although I probably learn more, I get flustered and don’t fly at my best, but I do enjoy the challenge immensely.

So, today’s lesson and another beautiful day for it. Hardly any wind at EGNT. Scott was there as I did the pre-startup,post-start checks. I was doing his checklist flow, but forgot about switching the radio off before starting. A good habit to get into in case I fly an older model where the starting current can blow the radio.

For some reason, Tower had a problem hearing me. We weren’t sure if it was my headset or Tower was doing something else when I called for clearance. Later transmissions seemed to be heard fine. Although, Scott had problems hearing me. Will need to keep an eye on that. Or probably better to keep an ear on it !! I think we sorted it later by me pushing my volume up, but it’s a bit of a blur.

We taxi’ed to Foxtrot and were asked to Line up and Wait on 25. That’s a first for me in a helicopter.

No sooner had we got in position than we were given the “GO”. Once we were on the climb after the initial turnout, it was instrument time. We’d forgot the goggles, but to be honest it didn’t make any perceivable difference. Once you focus solely on the instruments, the scanning you need to do stops you looking out anyway. The only downside is you don’t know how much your peripheral vision is helping you out, but I didn’t feel like it was helping much.

So, we did climbs, turns by instruments and they went fine. I think I stayed within 100 feet of any altitude and the headings were +/- 15′, so I was happy with that. At this point, I was feeling in control of everything and on top form mentally.

As the flight progressed, the headset problems left Scott a bit frustrated. I was struggling to hear him over the radio banter. I think I needed to tweak some headset knob, but we were too engrossed to bottom it out, or at least I was. His frustration with my headset, started getting me on edge and my performance started to wane a little.

Once we’d done the instrument flying, we concentrated on Confined Area Landings. Scott had done an excellent and extremely thorough briefing before we even took off and I felt full with information, overflowing even. But, often, things are easier when you actually do them.

So, confined area landing as far as I can remember, involved a recce circuit to work out angles of approach the confined area, and possible departure angles. Then a lower circuit (approx. 1,000 feet) to look for any obstructions etc..….

Then an approach with an abort decision altitude to attempt a landing, but with a decision to abort if anything untoward is spotted.

On one of the downwind legs, we rolled back to 53 knots, maintaining level flight and recorded the power required, which I think was 17.5 MAP. Take that away from 23.5 MAP (max continuous for today), gave us 6inches MAP to play with. Ample for a confined area approach. The first attempt, I had misunderstood and thought we were going to go around, so I was too high to get in, which is what Scott wanted. With me now understanding we were going all the way in to a 5 foot hover, we did a tight circuit for a second attempt.

It felt quite a shallow approach given the steep approaches I did with Steve yesterday. My understanding after yesterday’s lesson was that it was a steep approach, but Scott had me come in quite shallow. But, we made it this time, although I did lose balance which nearly required Scott’s intervention. He was at full alert for a second before I got it under control. Not even sure why it got out of balance. Weird. I was pulling collective, which normally requires left pedal, but I had needed to give right. Bizarre !

Anyway, we came to the hover in this kind of dip in a hill and we had raised ground all around us. It was great. We then did some pedal turns, but cleverly, he had me move the helicopter to the right, before giving right pedal. In this way, we’re sure that the tail rotor isn’t going to hit anything as we’ve just come from the place the tail rotor is going to turn through. Then when we’ve done 90′ turn, we rinse and repeat until we’ve scanned the whole area. It worked a treat and the tail rotor didn’t hit anything ;-)

With the area now clear for departure, we needed to work out how much power we had available. I think we were showing 23.5 to to hover in ground effect (IGE), leaving only 1inch of MAP to spare, so we ideally needed to do an on-the-skids takeoff. But as we hadn’t landed, this wasn’t possible, so we had to do an IGE transition. It worked a treat and we headed back to Newcastle :-)

On the way back, we had a nice view of a Tornado streaking past. Hopefully, I caught it on video. Will check tomorrow if I get time. Steve was with his student at the plateau at the same time we were there and both helicopters were flying back at the same time. And I think Steve’s student had the better view of the Tornado, which isn’t necessarily a good thing ! ;-)

We followed Steve’s helicopter back and although it wasn’t quite a formation landing, we were only half a mile behind them on Base Leg and down the runway which was neat.

We taxi’ed back and then I did a shitty landing, rating of 4/10 on the dp landing scale. There was sideway’s movement at the just wrong moment, so I had to lower the collective to plant us on firmly, avoiding Dynamic Rollover.

All in all, a hectic, very taxing, but thoroughly enjoyable experience. I’ll need much more practice at these, but Scott was very complimentary about the first attempt, which was well received. I always think I’m doing worse than I am. I think it’s because I’m not flying my best with Scott generally. I haven’t done a good landing with him yet !

I’m writing this and sense myself being far too self-critical, but that’s me. It’s the way I improve I think by critiquing myself harshly. Always nice to be told that it’s gone well though.

Lesson booked for everyday next week apart from Thursday.

Posted in Helicopter Training | No Responses »
Tags: , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

Lesson 27 – 24th August 2009 – 1450 – 60 minutes – Total so far – 28 hours 4 mins

Monday, August 24th, 2009

Well, my head was buzzing and in overload after this lesson.

It wasn’t so much a lesson, although I did learn stacks, rather a mini trial practical test with the senior instructor (soon to be examiner) Scott.

To say I wasn’t ready for the onslaught that is Scott is probably an understatement. A very different style to Steve, but not in a bad way. Steve had said that I’d benefit from some time with another instructor and as per usual, he was right.

Steve has a very easy going relaxed way. He never comes on the controls these days unless he’s demonstrating a maneuvre and is subtle when I cockup, staring at a button I’d forgot to click, or something along those lines. Scott, on the other hand, was very full on. But, it really challenged me and I liked that. It gave me a new perspective and I certainly learned a lot. There was one downside, I got flustered which translated into what I thought was a poor performance.

I’ll not remember everything that happened in the hour, but I’ll try……

Scott wanted to be there when I started her up. I’m glad about this, because I think I’ve been doing the startup procedures in a bit of a non-standard way. Note to self…..

Consult the Flight Manual to work out how much manifold pressure I can pull continuously and at max, given temperature and pressure altitude.
Before starting, turn the radio off.
After starting and checking starter motor has disengaged, flick all the switches on (incl clutch)
Scott gets the clearance when he’s ready to go, whereas I’d been doing it while waiting for the clutch to fully engage.

So, with the engine started, I lifted off. I don’t think he helped at this point, so that was a good sign. Post liftoff checks were done. All fine so far.

Taxi to Foxtrot ensued, and then I called that we’re ready for departure. Cleared to depart north, I headed off (as I normally do), but Scott later pointed out that I should have done some pre-departure checks. I was too flustered to remember what they were. I’ll have to ask next time.

Normally, I don’t forget trim and transponder at 500ft, but it was 800ft before I remembered. God help me for the real test !!

He suggested FREDATT checks (Fuel, Radio, Engine, Direction, Altitude, Trim and Transponder) at 500 feet, which normally I’ve only been doing approaching the airfield on return.

So, we did them. He asked me what altitude I was going to fly…2300 feet I told him.

Which I kept initially, but I think I lost it later on.

Once out of the zone, we did a set of maneuvres. REAL BASIC STUFF !!! STUFF I SHOULD BE ABLE TO DO WITHOUT A PROBLEM. First off, was a turn. 15′ degree rate of turn in one direction through 360′. Well, I gained or lost (can’t remember) 200 feet during the turn. Come on David, get a grip !!!

Scott explained a few things and then I did the same turn but in the other direction. This time, it was much better, but there could have been less error.

Oh, before I forget !! I had been using the slip ball for seeing if we were in balance or not. Scott explained that it doesn’t work !!! And it’s not a problem with the helicopter, it’s because the heli is set to show balanced when on the ground, but an R22 flies left skid low, so it doesn’t read correctly in flight !! So, I need to get used to using the string on the bubble. Note to self…..

Pedal to the window with no string in !!!!

So, of course, that threw me completely, because all this time I’d been using the balance ball thing. In fact, in hindsight, that was the thing that probably made me flustered for the whole thing, because all my flying was requiring this new skill of “watching the string” ! ;-)

We then did some climbs and descents. For the climbs, I went over the manifold pressure I should have a few times, until I understood that I shouldn’t go over 23. For all the descents I remembered Carb Heat 50% of the time. 50% of the time would definitely be a fail !!! You need to rememeber it 100% of the time. The risk of icing today was particularly bad, because we went through rain a few times !!

Another interesting thing he said was if there is any rain, no questions, apply Full Carb Heat !!

We then did an autorotation to lose height ie a gradual lowering of the collective. I remembered Carb Heat this time !! :-) That went fine. But of course, I was watching the string which caused me to have to think too hard to worry about everything else (rotor rpm), but thankfully either Scott did rotor rpm, or I did it without thinking. Can’t remember, I was too flummoxed ! ;-)

Apparently, an auto is not complete until you look upwards (for the climb away) and cancel carb heat (NOTE TO SELF!)

We then did an autorotation for range as if the engine failed (75 knots). Faster lowering of the collective and maintaining 75knots went ok, but then I was thrown when he asked me to keep the throttle closed. I’ve never done any throttle work in the autorotation before, but pleased I got a chance to do it. It’s started me thinking on new trains of thought.

I think we then did another one. They felt ok.

By this stage, it was time to return and the rain was falling heavily over EGNT.

Scott made lots of R/T calls because I couldn’t understand things. I really must get my own headset. It was much worse today, and I’m normally comfortable with the Newcastle R/T so either the headset’s at fault (or more likely I was too flustered).

We were asked to hold at the northern airport boundary for 2 inbounds. And then we were asked to nip in before another big jet. Scott asked what would I do if asked to expedite when I was solo. I had previously expedited solo, so I suspected that that wasn’t the right answer and I was right. Don’t expedite solo !! Shame, ‘cos it’s lots of fun, but I knew where he was coming from !

Taxi next to the bowser and then I was gagging for another perfect landing like the other day, but it was messy. Not a 30-second messy dp special that I have previously done consistently, but it wasn’t like the beauties that I’d managed at Carlisle and Eshott.

I did a couple of attempts, but aborted them. Scott then demo’ed one and explained something which has now been lost in fluster land, but it stayed with me enough to do a half decent final landing based on whatever he’d said.

After we’d shut it down, he took me around the helicopter asking me what bits and bobs were. That was very interesting. I think I got 1 or 2 things right, but the other 6 were half-decent guesses that were wrong !! ;-) WHY DIDN’T HE ASK ME WHAT THE THING THAT GOES ROUND ON THE TOP IS ? OR THE FAN THING AT THE BACK END !? He probably didn’t know himself I expect ! :-)

So, all in all, a huge learning experience, but I left feeling a bit bamboozled. It’s that feeling where I know I’ve learned LOADS, but it’s not all sunk in yet. I’m pretty sure that, tomorrow, things will keep coming back to me, with a “oh yes” kind of moment as they sink in.

Thoroughly enjoyable and extremely valuable lesson in terms of things learned, but not showing my best skills ‘cos of being flummoxed. But, no pain, no gain. If I hadn’t learned the countless things I did, I may have flown better because I wasn’t flummoxed, but not have been a better pilot because of it (if that makes sense). I know what I mean ! :-)

But, to end on a positive, and to my big surprise, as the whole lesson felt like I was doing things wrong, Scott was very complementary. He asked me how many hours I’d done, and said I was “well ahead of the game and flying excellently” or something like that.

Video to follow when time permits

Posted in Helicopter Training | No Responses »
Tags: , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,